Espressif ESP32-S3-DevKitC-1-N8R2, ESP32-S3-WROOM-1, 2MB PSRAM, 8MB Flash
Product number: ADA5310
Description
Product information "Espressif ESP32-S3-DevKitC-1-N8R2, ESP32-S3-WROOM-1, 2MB PSRAM, 8MB Flash"
The ESP32-S3-DevKitC-1 is an entry-level development board equipped with the ESP32-S3-WROOM-1, a universal Wi-Fi + Bluetooth LE MCU module that integrates full Wi-Fi and Bluetooth LE functions. This version is equipped with the ESP32-S3-WROOM-1 (PCB antenna) with 8MB Flash and 2 MB PSRAM.
Please note: The S3 is similar to the ESP32-S2 - but also has a dual core and Bluetooth LE (not classic!) However, there is minimal support for this dev board. For example, at the time of writing there is no support for Arduino or CircuitPython - only for ESP IDF! Please buy it if you are developing with the S3 and don't mind it not working 100%.
Most of the module's I/O pins are split across the headers on either side of the board for ease of connection. Developers can either connect peripherals with jumper wires or mount the ESP32-S3-DevKitC-1 on a breadboard. We particularly like that there is a debug UART/USB port and a separate native USB port so you can upload, debug and transfer USB at the same time.
At the heart of the module is an ESP32-S3FN8, an Xtensa® 32-bit LX7 CPU running at up to 240 MHz. You can switch off the CPU and use the power-saving co-processor to constantly monitor the peripheral devices for changes or exceeding threshold values.
The ESP32-S3FN8 has a wide range of peripherals including SPI, LCD, camera interface, UART, I2C, I2S, remote control, pulse counter, LED PWM, USB Serial/Jtag, MCPWM, SDIO host, GDMA, TWAI® controller (compatible with ISO 11898-1, i.e. CAN specification 2.0), ADC, touch sensor, temperature sensor, timer and watchdogs as well as up to 45 GPIOs. It also has a full-speed USB 1.1 On-The-Go (OTG) interface to enable USB communication
There are three mutually exclusive ways to power the board:
Please note: The S3 is similar to the ESP32-S2 - but also has a dual core and Bluetooth LE (not classic!) However, there is minimal support for this dev board. For example, at the time of writing there is no support for Arduino or CircuitPython - only for ESP IDF! Please buy it if you are developing with the S3 and don't mind it not working 100%.
Most of the module's I/O pins are split across the headers on either side of the board for ease of connection. Developers can either connect peripherals with jumper wires or mount the ESP32-S3-DevKitC-1 on a breadboard. We particularly like that there is a debug UART/USB port and a separate native USB port so you can upload, debug and transfer USB at the same time.
At the heart of the module is an ESP32-S3FN8, an Xtensa® 32-bit LX7 CPU running at up to 240 MHz. You can switch off the CPU and use the power-saving co-processor to constantly monitor the peripheral devices for changes or exceeding threshold values.
The ESP32-S3FN8 has a wide range of peripherals including SPI, LCD, camera interface, UART, I2C, I2S, remote control, pulse counter, LED PWM, USB Serial/Jtag, MCPWM, SDIO host, GDMA, TWAI® controller (compatible with ISO 11898-1, i.e. CAN specification 2.0), ADC, touch sensor, temperature sensor, timer and watchdogs as well as up to 45 GPIOs. It also has a full-speed USB 1.1 On-The-Go (OTG) interface to enable USB communication
There are three mutually exclusive ways to power the board:
- USB-to-UART port and ESP32-S3 USB port (either one or both), standard power supply (recommended)
- 5V and G (GND) pins
- 3v3 and G (GND) pins
- ESP32-S3-WROOM-1: ESP32-S3-WROOM-1 is a powerful, generic Wi-Fi + Bluetooth LE MCU module that has a variety of peripherals. It provides acceleration for neural networks and signal processing tasks. ESP32-S3-WROOM-1 comes with a PCB antenna.
- 5V to 3.3V LDO: Power regulator that converts a 5V supply to a 3.3V output.
- Pin Headers: All available GPIO pins (except the SPI bus for the flash) are distributed on the pin headers on the PCB to facilitate connection and programming. See header block for details.
- USB-to-UART connector: A micro USB connector is used to power the board, to flash applications to the chip and to communicate with the chip via the integrated USB-to-UART bridge.
- Native ESP32-S3 USB port: ESP32-S3 full-speed USB OTG interface, compliant with the USB 1.1 specification. The interface is used to power the board, to flash applications to the chip, to communicate with the chip via USB 1.1 protocols and for JTAG debugging.
- Boot button: Download button. If you press and hold Boot and then press Reset, the firmware download mode is started, allowing you to download the firmware via the serial interface.
- Reset button
- USB to UART bridge: A single USB to UART bridge chip enables transfer rates of up to 3 Mbps.
- RGB LED: Addressable RGB LED, controlled via GPIO48.
- 3.3V Power On LED: Lights up when the USB power supply is connected to the board.
Properties
| Zolltarifnummer: | 85176200 |
|---|---|
| Brand: | Espressif |
| Country of Origin: | China |
| Gross Weight (kg): | 0.353 |
| Manufacturer ID: | ESP32-S3-DevKitC-1-N8R2 |
| Product ID: | ADA5310 |
Manufacturer
Espressif
Espressif Systems: Everything for your IoT project
Espressif Systems is a leader in the development of wireless communication and Internet of Things (IoT) solutions. Founded in 2008 by a team of experienced engineers and technicians, Espressif has quickly earned a reputation as an innovative and reliable partner in the IoT industry. The company is headquartered in Shanghai, China, and operates offices in various countries around the world. One of Espressif's best-known products is the ESP32, a high-performance, low-power microcontroller that supports both WLAN and Bluetooth and is used for a variety of IoT applications. The ESP32 is particularly known for its low power consumption and high performance, which makes it ideal for applications such as smart homes, wearables, and IoT devices. Espressif also offers development kits, tools, and documentation to support the development of products and applications, particularly through the use of the ESP32. The company works closely with customers and partners around the world to help them quickly and successfully implement their IoT projects.
Manufacturer and safety information
Manufacturer information
Espressif Systems
#204, Block 2, 690 Bibo Road
CN 201203 Shanghai
https://www.espressif.com/en
info@espressif.com
WEEE number: 17968585
Person responsible for the EU
TME Germany GmbH
Dohnanyistraße 28-30
DE 04103 Leipzig
https://www.tme.eu/de/
tme@tme-germany.de
Safety instructions
Espressif Systems
#204, Block 2, 690 Bibo Road
CN 201203 Shanghai
https://www.espressif.com/en
info@espressif.com
WEEE number: 17968585
Person responsible for the EU
TME Germany GmbH
Dohnanyistraße 28-30
DE 04103 Leipzig
https://www.tme.eu/de/
tme@tme-germany.de
Safety instructions
- Keep the product out of the reach of children.
- Do not use in damp or wet environments to avoid short circuits.
- Protect from overheating and direct sunlight.
- Do not supply inputs and outputs with the wrong voltage. Observe the operating voltage (typically 3.3 V).
- Do not touch with bare hands or conductive materials when the board is in operation.
- Improper handling can damage components or cause a fire hazard.
- Only use with approved power supply units and accessories.
- When soldering or modifying the product, secure it properly and observe earthing.
- Dispose of in accordance with local regulations for electronic waste.
- Do not dispose of with household waste, but take to an electronics recycling centre.
- Dispose of batteries/power supply units separately and in accordance with their specific regulations.
Reviews
0
Login